Jun
22
ULTRALIGHT TEALITE ALCOHOL STOVE/POPCAN
By
TEALITE ALCOHOL STOVE checkout my blog @ threefloorsdown1.blogspot.com campinghiking BOB bugoutbag bol tealite pop can stove survival outdoors cooking fire ultralite wilderness soup holes funny survivalist jbweld beer dr pepper play hackysack knives brick rock youtube flame threefloorsdown1 three, gardening, striker, flintsteel, medical, first aid, camo, 4×4, deer,rabbit,squirrel,bird, hunting, sun solar cooking gardening, rocks, backpacking,hiking,mbd,matches,strike, tinder,girls,hay,grass,bark,wood, bushcraft,
25 Comments
June 22nd, 2010 at 5:07 am
@lanetaglio i’m not sure, i use nasil spray bottles as of now, but those give me 3-4 full uses if not more…lately this past season i just used popcan stoves cuz it wouldnt work aswell in below frezzing temps well without alot preheating & lost alot of het due to how thin it was. the wire gets hotter than the out part , so the flame follows the hottest part of the stove to make the peak flame
June 22nd, 2010 at 5:07 am
Great idea. What’s the primary purpose of the wire down the center? How many “1-Cup” Boils would you get out of an Elmers Glue container full of HEET? Thanks!
June 22nd, 2010 at 5:07 am
Great idea. What’s the primary purpose of the wire down the center? Thanks!
June 22nd, 2010 at 5:07 am
thanks..i think its a decent stove…try makin 1 yourself & test it out
June 22nd, 2010 at 5:07 am
Containers come from the most suprising sources. I find a little sheet metal know how, plastic or metal; glue or epoxy; cut a tube and plug it. plastic plumbing pipe and end.
you are right about the container.
June 22nd, 2010 at 5:07 am
i like the stive pretty well, but unless you find a small perfect sized container to carry it in…its prone to smashing cuz itss so fragile
June 22nd, 2010 at 5:07 am
nice Pressure tealight.
more fuel capacity never hurts.
June 22nd, 2010 at 5:07 am
lol @ buddys broken arm nice vid
June 22nd, 2010 at 5:07 am
take 4 tealites…press 1 inside the other..after u have 2 deff sections of tealights pressed….[-]..lightly put jb weld on the rim of 1..then lightly put it on top of the other…this also works with 2 seperate single tealites….using 4 & pressing 1 inside the other just makes its more ridged…..after your put it on the other…let it sit for about an hr….after that you can finish it by put jb weld around the side….the rod in the middle just a metal coat hanger peice
June 22nd, 2010 at 5:07 am
its two of them squeezed over one another and put insulation inside, 8 holes on top pocked with a needle, bottom seeled with jb weld, and a hole in middle the size of a syringe tip, as to fill, it holds 13 ccs of 91% rubbin alcohol
June 22nd, 2010 at 5:07 am
its two of them squeezed over one another and put insulation inside, 8 holes on top pocked with a needle, bottom seeled with jb weld, and a hole in middle the size of a syringe tip, as to fill, it holds 13 ccs of 91% rubbin alcohol
June 22nd, 2010 at 5:07 am
wut type of container are you using? because that is hard to believe…i’d like to see a video on that….is it this same type or an open tealite like jason klaus?
June 22nd, 2010 at 5:07 am
my tea light stove boils two cups in $ minutes right as it runs out of fuel
June 22nd, 2010 at 5:07 am
ya..it works pretty good once it gets warmed up
June 22nd, 2010 at 5:07 am
a decent tealight stove
good work, Did you test it in the cold?
thanks
June 22nd, 2010 at 5:07 am
great idea! very cool.
June 22nd, 2010 at 5:07 am
also if you use 4 tealites & press 1 into another it makes it alot more durable
June 22nd, 2010 at 5:07 am
also if you use 4 tealites & press 1 into another it makes it alot more durable
June 22nd, 2010 at 5:07 am
jb weld… the smoother the better. i found if you use grill paint to cover the jb weld. it wont burn when preheating the stove
June 22nd, 2010 at 5:07 am
what did you use seal the two t lights?
June 22nd, 2010 at 5:07 am
thankyou…it took alot of failures before i came up with it
June 22nd, 2010 at 5:07 am
Thats pretty brilliant!
June 22nd, 2010 at 5:07 am
Thank you so much! Love your videos been watching them this week!
June 22nd, 2010 at 5:07 am
jb weld should be around the auto section! google an image of it so you know wut your lookin for
June 22nd, 2010 at 5:07 am
Hey thanks so much, I’ll pick some heet up this week at walmart, where do I get the jb weld? Not sure what that is (I’m a woman I’m not man mind oriented here lol)